IntroductionTo the owner or user: This service manual isintended to provide you, and the maintenance orservice technician, with the information needed

After Utility Connections1. Level the cabinet, use the leg levelers on theend of the legs to adjust the cabinet height. (Legsshould have been installe

Component LocationMany components are serviceable from the frontwithout removing the side panels.Behind the front panel:•• Water pump•• Inlet water va

Initial Start UpAfter the final check list has been gone through,the ice machine may be started up.1. Open the water shut off valve; the inlet waterva

Initial Start UpNote: If the first batch of cubes are not all uniformdiscs, some ice machine cleaner should be addedto the reservoir.1. After ice has

Maintenance, Cleaning and SanitizingCleaning Schedule:••Scrub the outside of the cabinet once a weekwith soap and water.••Sanitize the bin interior on

Cleaning: Ice Machine Water SystemDissolve and Remove Minerals:1. Remove front panel.2. Move the ICE/OFF/WASH switch to OFF.3. Remove the splash guard

Refrigeration Schematic:Freeze Cycle:From the compressor, hot discharge gas ispumped to the condenser, either air or watercooled.At the condenser, hea

Harvest Cycle:The ice maker continues to freeze the water intoice until the ice next to the ice size thermostatprobe has become thick enough to force

Technical CharacteristicsTypical Cycle Time ••16 - 17 minutes @ 90oF. air and 70oF. waterTypical Harvest Ice Weight••3.8 - 3.9 pounds .Typical Low Sid

Service Diagnosis: SYMPTOM POSSIBLE CAUSE PROBABLE FIXNo ice is made, nothing operates Unit off, due to no power Restore powerUnit off, due to ICE/OFF

SpecificationsInformation regarding Model Number, SerialNumber, Ampacity and Maximum Fuse Size arelocated on the nameplate of the ice machine. Themode

SYMPTOM POSSIBLE CAUSE PROBABLE FIXNo ice compressor is operating No cooling due to low refrigerantchargeLocate leak, recover remainingrefrigerant, re

Service Diagnosis: SYMPTOM POSSIBLE CAUSE PROBABLE FIXIce is made, but will not harvest Will not harvest due to hot gasvalve not opening.Check for vol

Removal and ReplacementIce Size Thermostat:Before replacing the ice size thermostat, it shouldbe positively determined that it is at fault.1. Disconne

Removal and ReplacementWater PumpThe pump provides the force to move the waterfrom the reservoir to the freezing surface. Thepump does not need oil, b

VAPOR VAPOR TEMP. PRESS. TEMP. PRESS.(DEG F) (PSIG) DEG F) (PSIG)-20 17 70 146-18 18 72 150-16 20 74 155-14 21 76 161-

For The Installer: Environmental LimitationsThe ice machine must be installed indoors in acontrolled environment.Minimum MaximumAir Temp 550F. 1000F.W

InstallationWaterThe water supply for this ice machine has been incontact with many materials since it fell from thesky as rain. All rain is slightly

Capillary TubeBin ThermostatBracketFasten CabinetsTogether At BackWith Straps &Screws.Routing HoleStackingInstallation: Ice Storage BinAssembly:1.

Installation: SLD150 Hotel DispenserAssemblyThe ice machine must be placed onto the top ofthe dispenser, and the bin thermostat capillarytube routed i

Installation: Scotsman IS or RS DispenserAssembly:The assembly of the ice machine onto thedispenser requires two additional parts: an adapterkit and a

InstallationFor The PlumberSupply:Screw the 3/8" male flare (fitting shipped inpackage inside cabinet) into the 1/4" FPT fitting atthe back

InstallationFor The ElectricianThis unit must be on a separate 115 volt AC 60cycle single phase power supply. The maximumfuse size for this circuit is